Call (909) 391-3800

Go to…

Audi

Home / Audi

We Service and Repair all Audi cars

  • 2010 Audi A3

    Audi A3
    Mileage
    84,124
    Service Date
    5/6/2026
    Services Performed
    • Inspected vehicle ignition system and verified key is unable to turn. Pulled apart steering column and verified that ignition lock is faulty. A new ignition barrel assembly is needed at this time. After replacement, retest is needed to verify correct operation of key. This operation is competed!
    • Unable to move forward with check engine light diagnosis before repairing key issues first. After repairing key issues, started vehicle and noticed loud vacuum leak noise coming from engine bay. After inspecting found that intake flap actuator has broken off from intake manifold and is causing a large vacuum leak. Also noticed that the water pump is leaking as well and will need to be replaced while the intake manifold is off. Codes present are 08213, 08583, and 00768. After performing repair, all codes will be deleted and vehicle will need to be road tested to verify all systems are okay. After performing repair of intake manifold and water pump, cleared all previous DTC's and road tested vehicle. No check engine light has returned at this time and no leaks are present. BUT the ABS, Brake, and Traction control light are illuminated due to a faulty intermittent ABS hydraulic pump, Code 01276:014. Further diagnosis is needed to determine why ABS pump is faulty.
    • This operation is completed.
    • Operation: Replace Water Pump Assembly – Includes Coolant Drain/Refill and Intake Manifold Removal as Combination Labor Description: Performed removal and replacement of the engine water pump/thermostat housing assembly. Drained cooling system and recovered coolant as required. Removed engine cover, air intake ducting, PCV connections, and related components for access. Disconnected coolant hoses, electrical connectors, and mounting hardware from the water pump assembly. As part of required access, removed the intake manifold using combination labor procedures. Disconnected fuel rail, EVAP lines, MAP sensor, throttle body connections, and manifold fasteners. Inspected intake ports and manifold for carbon buildup or damage. Reinstalled intake manifold with new gaskets and torqued all fasteners to specification. Installed new water pump/thermostat housing assembly with new seals and hardware. Reconnected coolant hoses, electrical connectors, and all previously removed components. Refilled cooling system with approved coolant mixture and performed vacuum fill/bleed procedure. Verified proper coolant circulation and checked for leaks with engine at operating temperature. Cleared any related fault codes and performed final inspection.
     
    Anne L. gave our service a 5 star review on 5/8/2026

  • 2015 Audi A3

    Audi A3
    Mileage
    136,856
    Service Date
    4/8/2026
    Services Performed
    • Found 3 of the 4 bolts that mount the subframe to the body missing. Need to lower the subframe an inspect the threads and subframe. If it is okay then install all new hardware and alignment. This is a starting point.
    • After installing the bolts torqued to factory specifications, 70NM + 180 degrees, performed a alignment to set the steering wheel straight. Attempted to perform a steering angle sensor relearn to clear the warning lights. The relearn kept failing and code B116807 set. Which is steering angle sensor- mechanical malfunction. Found the steering angle sensor is integrated into the rack and pinion. Power and ground are present at the sensor. From the sub frame being loose, caused damage to the rack and pinion. We recommend replacing the rack and pinion with outer tie rods. Note… front pads 8mm, rear pads 8mm. The line feeding def to the injector is cracked and leaking.
    • Alignment
    • Removed and replaced DEF hose. Verified operation and road tested vehicle, def system is okay and no leaks at this time.
     
    Palmer L. gave our service a 5 star review on 4/8/2026

  • 2017 Audi Q7

    Audi Q7
    Mileage
    102,335
    Service Date
    10/16/2025
    Services Performed
    • Removed and replaced pcv valve, cleaned all sealing surfaces, and replaced intake manifold gaskets. Ran vehicle to verify no leaks and scanned for current dtc's. All systems test okay at this time.
    • Scanned vehicle and found DTC's P052EE0 and P227900. Both codes are related to PCV system performance indicating an issue within PCV. With engine running, observed excess Crankcase vacuum and noise dissipation by pulling oil cap and releasing vacuum pressure. After further tests were completed we have determined that the PCV has failed and is needed to be replaced at this time. We will also need (6) intake gaskets for the repair as well.
     
    Kevin G. gave our service a 5 star review on 10/24/2025

  • 2009 Audi Q5

    Audi Q5
    Mileage
    149,092
    Service Date
    4/28/2020
    Services Performed
    • After are A/C diagnosis we have found that the vehicle has a faulty blower motor and a blower control module. We need to replace both of the items first and then retest the system after repairs.
    • FRONT BRAKES @ ___8___MM REMAINING REAR BRAKES @ __8___MM REMAINING
    • Replace the lower outlet. Union
    • VALVE COVER GASKET – Remove & Replace – Both
     
    Venswella S. gave our service a 5 star review on 5/4/2020