FRONT BRAKES @ __6____MM REMAINING REAR BRAKES @ ___1__MM REMAINING AND DRUMS NEED TO BE REPLACED
Replace both Catalytic Converter as required.
The major oil leak is the front crankshaft seal. We recommend doing that first and rechecking the vehicle for further oil leaks soon after repair.
We scanned the computer and have the following codes: PO335-Crankshaft Positioning sensor circuit (A) PO420-CAT System below threshold P2441-Secondary Air Injection System switching valve stuck closed. We recommend a crankshaft positioning sensor, replace the air switching valve and update both studs so the new valve will mount, and replace both the front and rear converters. The clear the codes and retest after repairs. Then retest
Cesar V. gave our service a 5 star review on 4/16/2020
FRONT BRAKES @ __11____MM REMAINING REAR BRAKES @ __06___MM REMAINING
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [DOES NOT include disassemble or alignment.]
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [Includes: Bleed Brake System (where applicable). DOES NOT include disassemble or alignment (where applicable).]
WHEEL BEARING – Remove & Replace – AWD,Gas Rear,Hub Assembly,Both – [DOES NOT include wheel alignment.] – [Includes: Replace Inner and/or Outer Bearings, Cups, Seals and repack (where applicable).]
Alignment
Andre V. gave our service a 5 star review on 4/7/2020
FRONT BRAKES @ __10__MM REMAINING REAR BRAKES @ __8___MM REMAINING
Replace front brake pad linings and machine front brake disc rotors. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle.
Ashley L. gave our service a 5 star review on 3/16/2020
COOLANT TEMPERATURE SENDER OR SENSOR – Remove & Replace – V8
FRONT BRAKES @ ___8___MM REMAINING REAR BRAKES @ __5___MM REMAINING
THERMOSTAT &/OR GASKET – Remove & Replace – V8
We scanned the computer and have the following codes: PO934-Line pressure sensor circuit low PO868-Line pressure low PO933-Hydraulic Pressure sensor range/Perf PO869-Line pressure high PO935-Hydraulic Pressure sensor circuit high ________All Transmission codes___________ PO456-Small EVAP leak-Needs a smoke test to diagnose. P2181-Cooling system Performance PO128-T-Stat Rationality For the last two codes we recommend a new thermostat and gasket. Then recheck operation. For the EVAP leak we recommend a smoke test be performed and advise. After we replaced the thermostat we ran the vehicle to operating temp but were receiving inaccurate temp readings. We checked the coolant temp sensor and found corrosion in the coolant temp sensor plug. We recommend replacing the coolant temp sensor and then performing a head gasket check to make sure the head gasket is not blown. After our test we have found that the head gaskets are not blown and the cooling system is operating correctly at this time.
Ralph D. gave our service a 5 star review on 3/10/2020
We performed a smoke test and found the seal around the fuel cap is leaking. We replaced the fuel cap.
We scanned the computer and have the following codes: PO121-Throttle Positioning sensor 1 performance PO171*-Fuel trim system lean bank 1 PO174-Fuel trim system lean bank 2 PO455-Evaporative Emissions Large system leak detected PO573-Brake light switch circuit The throttle positioning code means that the throttle body needs to be replaced. This is also causing the two other codes, PO171 and PO174. We need to perform a smoke test to determine the EVAP code, PO455 code, then report the problem with that. The brake light circuit code is a faulty brake light switch.
Neil Z. gave our service a 5 star review on 3/7/2020