CRANKSHAFT POSITION SENSOR – Remove & Replace – PreRunner,V6 w/A/C Compressor Removal – [Includes: R&I Air Conditioning Compressor. DOES NOT include Air Conditioning System recover, evacuate and recharge.]
ELECTRONIC CONTROL MODULE – Remove & Replace – ECM
We scanned the computer and have the following codes: PO335-Crankshaft Position Sensor "A" Circuit. When we snapped the throttle we can get the check engine light to come on. We checked the scanner and the crankshaft position code comes on. We then tested the sensor and find it out of range. We recommend replacing the sensor. We replaced the sensor and cleared the codes. We test drove the vehicle and during our test drive we snapped the throttle and the check engine light came back on. We scanned the computer and found that it appeared that the computer was not recognizing the crankshaft positioning senor circuit. The computer appeared to see half the sensor reading. We felt that the computer was also the problem. We recommend replacing the computer (PCM). We replaced the computer and then had the computer flashed. We test drove the vehicle again and snapped the throttle and the check engine light came back on again. We scanned the computer and the code PO335-Crankshaft positioning sensor circuit code came back on.
Fuel
Program Computer
Darin L. gave our service a 5 star review on 10/21/2020
A/C COMPRESSOR – Remove & Replace – PreRunner,V6 – [Includes: R&I Alternator.] – [DOES NOT include Air Conditioning System recover, evacuate and/or recharge.]
Service air conditioner. Check condition of all belts and lines. Evacuate and recharge with reclaimed R-134. Test system performance. Note center vent temp Max Cool/High___42.8____ Connect gauge set and advise of High and Low pressures @ 1500 Rpm. Ambient_____88____High___240____Low___28____ Inspect Belts, hoses, fan clutch, and electric fans if equipped and advise of recommendations.
We checked the charging system and found the alternator charging at 13.93 volts loaded and 13.63 not loaded. The battery has 609 cca out of 710cca, The charging system is good. We did see that the front of the compressor looked like it was burn't. We inspected that and found that to be the problem. It appears that the clutch has burnt and the compressor is frozen. We recommend a new compressor, condensor/drier, and expansion valve.
Thomas A. gave our service a 5 star review on 10/10/2020
Lube, Oil, and Filter Special. Change the engine oil and filter, check all fluids, undercarriage, belts and hoses, and tire pressures. Then advise customer of any concerns.
Dan C. gave our service a 5 star review on 9/3/2020
Replace front brake pad linings and machine front brake disc rotors. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle.
We checked the tie rod ends, lower control arms and front struts and all look good. The right frnt brake is metal to metal and that is what you are hearing. We recommend front brake pads and rotors.
Krestal L. gave our service a 5 star review on 7/31/2020
FRONT BRAKES @ ___6___MM REMAINING REAR BRAKES @ _2__MM REMAINING-Drums-okay
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [DOES NOT include disassemble or alignment.]
SHOCK &/OR STRUT ASSEMBLY – Remove & Install or Remove & Replace – Both – [Includes: Bleed Brake System (where applicable). DOES NOT include disassemble or alignment (where applicable).]
The front suspension is in good shape at this time.
Alignment
Labor
Todd T. gave our service a 5 star review on 6/5/2020
DISC ROTOR – Remove & Replace – Front,Both and replace Pads (if necessary). DOES NOT include refinishing.]
Lube, Oil, and Filter Special. Change the engine oil and filter, check all fluids, undercarriage, belts and hoses, and tire pressures. Then advise customer of any concerns.
Romeo B. gave our service a 5 star review on 5/8/2020